Move in direction b to turn off the starter choke. Remove moveable sheave and note the number of spacer washers. Do not lubricate the bushings! Improperly purging the exhaust system. Place the machine on a level place. The diaphragm should fit properly in the carburetor body.
Riding on public roads can result in collisions with other vehicles. Start the engine and keep it idling until oil begins to seep from the oil gallery. Position hose along side of carburetor as shown in your service manual. Install the purging bolt and tighten it. Insert new brake pads into the caliper.
Light will be visible between the needle and needle jet if it is worn. Inflate the tires very slowly and carefully. See pages 8-9 ~ and fasteners before a ride. The pre filter should be cleaned before each ride using the following procedure: 1. Start machine and slowly increase speed to 30 mph. The tires listed below have been ap- dislodge from the rim under severe proved by Yamaha Motor Co.
Slowly turn the adjusting bolt counter- wise to increase the free play. The chart below is printed only as a re- minder to you that the maintenance work is required. During this time chain tension should be watched very closely and loads to the chain should be kept light. If the damage or vehicle performance problems. There is a chain break-in period of approximately 100miles or two 2 tanks of fuel.
If necessary, apply 14 inches in depth. Install the oil filter, O-ring, and oil filter Oil quantity: cover. This manual pdf download is a great guide to help you carry out simple or more advanced maintenance and repair work efficiently and correctly. Be sure to re-attach the bowl drain hose after performing the test. Inspect driven clutch faces for wear or damage. When inspecting the battery, be sure the breather hose is routed correctly.
Carefully assemble caliper body, making sure O-rings are properly positioned in groove. Remove the dipstick and drain bolt to drain the oil. Wipe off any grime from the threads and tight- en to the specified torque. The bottom part of the chain should be taught during inspection. On extremely slippery surfaces, such as ice, go slowly and be very cautious in order to reduce the chance of skidding or sliding out of con- trol.
Install recoil housing gasket and recoil housing. Your Yamaha dealer has a variety of an accessory that limits your ability to move genuine Yamaha accessories. . Ride cau- tiously in unfamiliar areas. If necessary, remove the rear brake line from the master cylinder. Most A diagnostic tachometer must be used for this adjusting should be left to a Yamaha dealer procedure. Remove nut from puller rod and take installation tool and clutch cover off rod.
This adjust- ment however, should be left to a professional Yamaha service technician. This manual is also a very reliable source of information that will make you, in time know more and more about your vehicle and how to prevent future problems from happening!! Replace diaphragm assembly if diaphragm is damaged. Lube splines with a light film of grease. Store it in a dry place and recharge it once a month. With the purchase of this Yamaha, you can now appreciate the high degree of crafts- manship and reliability that have made Yamaha a leader in these fields. A fuel level test allows you to observe the height of the fuel in the float bowl without removing the carburetor. Driveshaft components are precision parts.
Apply 5 inches Hg vacuum to the pump fitting. Never climb hills with excessively slippery or loose surfaces. Never open the throttle suddenly or make sudden gear changes. Each section of this manual provides comprehensive information on the operation of major systems, diagnostics, troubleshooting, overhaul, as well as the removal and installation of major components. Torque the slide pin to 30--35 ft. Tighten the wheel nuts to the specified torque. Replace the air filter every 50 hours, and possibly more often in very dirty conditions.
Performing the scheduled maintenance is very important. Warm up the engine for several minutes and stop it. Use electric starter to see if there is compression. Install the nut with its tapered side towards the wheel. Use no more than the following pressures when seating the tire beads. Other information that might describe this product! Refer to parts manual for more information.