Automatic tuning is effective when station signals are strong and there is no interference. A humming sound is Incorrect cable connections. You can also use the automatic and manual preset tuning features to store up to 40 stations A1 to E8: 8 preset station numbers in each of the 5 preset station groups. Presence, surround, and surround back room size. The advanced setup menu offers additional operations to adjust and customize the way this unit operates. Connect the power cable of your other components to these outlet s. Red: positive + Black: negative — Insert one bare wire into the hole on the side.
Refer to the diagrams in the table below to understand the speaker layout for each sound field program. Ideally, each speaker should be the same distance from the main listening position. However, the advanced setup menu parameters will not be initialized. Adjusts the amount of time taken for the dense, subsequent reverberation sound to decay by 60 dB at 1 kHz. To change sound field parameter settings to suit your listening environment, see page 66 for details. Change the initial settings indicated in bold under each parameter to reflect the needs of your listening environment. See page 22 for connection information.
The preset station group and number appear in the front panel display along with the station band and frequency. This is useful if you want to balance the level of each input source to avoid sudden changes in volume when switching between input sources. If you experience poor reception quality, install an outdoor antenna. If the signal from the station you want to select is weak, tune into it manually. Adjusts the apparent size of the surround sound field. Check that the songs currently stored on your iPod are playable. The sleep timer has set this unit to the standby mode.
Shipping to: United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech Republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, Korea, South, Indonesia, Taiwan, South Africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi Arabia, United Arab Emirates, Qatar, Kuwait, Bahrain, Croatia, Republic of, Brazil, Chile, Colombia, Costa Rica, Panama, Trinidad and Tobago, Guatemala, El Salvador, Honduras, Jamaica, Uruguay. Not all of the following parameters are found in every program. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Note Be advised that there may be no or not enough sound output from speakers depending on the type of input source being played back. This channel is counted as 0. Parameters for headphones have been set for each sound field so that accurate representations of all the sound field programs can be enjoyed on headphones.
The frequency range of this channel is from 20 Hz to 120 Hz. Control range: 0 to 100% 2ch Stereo 2-channel stereo direct. Set the appropriate library code to select and operate the desired component with the supplied remote control. Adjusts the volume of the reverberation sound. However, this is not possible in most home situations. You can also enter the channel number directly to select the desired channel by using the Direct Number Access mode see page 59.
Although you do not have to change the initial factory settings, you can change some of the parameters to better suit the input source or your listening room. Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect. . Use this feature to set the speaker impedance of this unit so that it matches that of your speakers. It creates virtual speakers to reproduce the natural sound field. The preset channel number appears in the front panel display. This changes the apparent size of the acoustic environment over an extremely wide range.
The following table shows the function of each control button used to control other components assigned to each input selector button, , and. Sound is heard from Incorrect cable connections. Only iPod Click and Wheel , iPod nano, and iPod mini are supported. You must set the appropriate remote control code for each input source see page 92. Refer to the operating instructions for those components. Hold down this button for more than 3 seconds to start automatic preset tuning see page 47.
The larger the value, the stronger the reverberation becomes. All digital input jacks are compatible with 96-kHz sampling digital signals. Change the initial settings indicated in bold under each parameter to reflect the needs of your listening environment. In this case, set one of the alternative codes to operate this unit separately. The larger the value, the larger the surround sound field becomes. Press one of the input selector buttons or set up.
There is distortion, and There is multi-path interference. You can then recall any preset station easily by selecting the preset station number. . . .