In this section we will describe some other important camera features. You must select either the date or time for stamping your prints. Is the flash mark blinking in the viewfinder? Set the remove the lens cover, and look through the mode dial to P. Available Options the flash button to raise the built-in flash unit. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Press the shutter button lightly to restore the camera to full operation. Formatting a used card deletes all the images stored on the card, so you should frequently copy images to a computer where they can be stored safely. Select or cancel all pictures for printing. We recommend that you spend some time taking test shots and experimenting with all of the features before you take important pictures. The card access lamp blinks while the images are being deleted and then goes off after all the images have been deleted. In the same way, attach the other end of the strap to the eyelet on the other side of the camera. A variety of matched add-on lenses deliver the flexibility digital photographers need to maximize creativity.
With the camera can use the correct methods to set the focus and exposure for the conversion lens. The card access lamp blinks while the card is formatting and then goes off after formatting has been completed. Twist the zoom ring to the left to enlarge the size of the subject T: telephoto , or turn it to the right to reduce the size of the subject W: wide-angle. If the error message occurs again, refer to the table below to solve the problem. This chapter describes only the basic procedures for taking and viewing pictures. However, you can lock the exposure by pressing the button before pressing the shutter button. P Program mode The camera automatically selects the best aperture value and shutter speed according to the brightness of the subject.
Equivalent to 35 - 140 mm lens on 35 mm camera. As Control panel the aperture is closed, the aperture value increases. Attach the dedicated external flash unit to the hot shoe. Every time To enter the playback mode so you can view you move the dial one position to the left, the images, set the mode dial to , or with the number of images displayed in the index mode dial set to P, A, S or M, rapidly press the increases 4, 9, 16. Available Options the flash button to raise the built-in flash unit. The camera can lamp is not blinking.
Control panel Viewfinder Monitor When the white balance button. The destination card is not inserted in the camera. View and download olympus camedia li 10c user manual online olympus battery charger user manual camedia li 10c battery charger pdf manual download. Set the mode dial to P, A, S, or M. Open the built-in flash, and set the camera in the fill-in flash mode displayed in the control panel and then take the picture with the flash. In order to achieve the effect of a floating subject, open the aperture to take the picture. Zoom Shooting Range 60 cm 23.
Year Month Day Hour Min. Even with the remote cable connected to the camera you can still release the shutter by pressing the shutter button. Bewahren Sie diese Anleitung bitte zur späteren Bezugnahme auf. For example, the same sheet of white paper held under sunlight may appear tinged with red when held under an incandescent light. Menu button Press to open menu in the monitor.
With one press on the shutter button, you can shoot up to 4 rapid exposures in the sequential mode. Three settings are available for viewing the shot immediately after it is taken. In this section we will describe some other important camera features. Return To Our 802,003,601 Note: All photographs and page content Copyright © 2000 Steve's Digicam Online, Inc. Physical Views We'll go into more detail on the controls and features on the next page.
Press the The format icon and message are displayed on the monitor while the selected card is being formatted. To select the flash mode, hold down the flash mode button , and then turn the main dial or sub dial button to the left or right until you see the desired setting. Continue to turn the dial until you see the desired combination of flash control setting marks, and then. If you see Card 0 blinking in the viewfinder The memory card is full and you cannot continue taking pictures with the card. This file format has been developed by Olympus for viewing and processing with our own software.
General Precautions If you have any questions about this product, please consult your nearest Olympus dealer in the provided Authorized Distributors List. Press and hold down the flash mode button , and then turn the main dial or the sub dial. Problem Did you set the date and time? For more details about the shooting distances and ranges for conversion lenses used with this camera, please refer to the Olympus web site. Card cover lock While pressing here, slide up. On the arrow pad, press to move the green highlight to the sleep mode mark On the arrow pad, press move the highlight to the right.
In P, A, S, or M mode press twice rapidly to enter playback mode, press again to leave playback mode. You can enlarge the single- image display, or even display several images at once with the index display. If the lens cap is attached, remove Press the latches inward and pull the cap off. This display and make sure that the mark for the recorded date or time can be stamped on s Summary of the content on the page No. Images which have been protected are not deleted.