2007 yamaha r1 main fuse location. 2007 Yamaha R1 Main Fuse Location 2019-01-24

2007 yamaha r1 main fuse location Rating: 5,8/10 1522 reviews

Yamaha R1 Fuse Location

2007 yamaha r1 main fuse location

Remove and save the two screws that secure left rear fender support to motorcycle frame. My brother-in-law's 2001 has had this problem for several months and I finally took a look at it this weekend. Align lower bracket hole with footpeg mounting hole in frame. Plastic shrouds — on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Ambient temperature should be at least 50 °F 10 °C for proper adhesion of the light pods and controller box to vehicle surfaces. Alas it was not to be! Install the two screws, removed in Step 2, in fender support.

Next

Where is the fuse box location on Yamaha

2007 yamaha r1 main fuse location

This is a multi-function switch thatcontols turn signals, brake lights, and flashers. The black gizmo is a rubber retention device. I took the plastic housing off the steering column unscrew the steering wheel tilt handle and found the left turn signal wire was coming out of the plastic box as I tilted the steering wheel up and down. Do not tighten screws at this time. The switch is going bad, so you'll have to replace it, and this supposedly involves removing the steering column.

Next

Reading : 2007 Yamaha R1 Fuse Box Location

2007 yamaha r1 main fuse location

Your answer lead me right to the problem. There is not enough slack in the wires and the will break over time if you use the tilt function regularly. I made this video so that it will help you guys. Next, remove the fuse box from the battery box, by pushing it out from the back. When this occurs, have a Yamaha dealer check the self-diagnosis system. Good luck and have a nice day. Disconnect the voltage regulator 1 at both connectors.

Next

SOLVED: 2005 Yamaha YZF

2007 yamaha r1 main fuse location

It is strongly recommended that you install new exhaust gasket at this time. I pushed in the connector and everything started working fine, what a relief. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Can I just bolt an extension cable to the existing one and then bolt it to the battery -ve and cover it up with insulation? I have the same problem on my 1992 econoline. For 2007 models: In addition, remove the lower voltage regulator cover 10.

Next

Where is the fuse box location on Yamaha

2007 yamaha r1 main fuse location

Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Kit Contents See Figure 2 and Table 1. On the left hand side clutch side remove the faux air filter cover in the same manner, you removed the one on the right. Install tool box 1 to mounting bracket 6 using button head screws 2 and washers 5. To get to it you may need to remove the cover that fits over the left side of the battery, shown in the above photo laying temporarily on top of the battery. Good luck and have a nice day.

Next

Yamaha r1 2004 model fuse box

2007 yamaha r1 main fuse location

Note: The bolt that this nut is on goes completely through the motorcycle. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Thanks so much for the info. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Align the 5 vibration dampeners with the 5 mounting holes in the mounting plate. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. A Linclon Mercury mechanic told me the problem was most likely in the hazard flasher switch on top of the steering column.

Next

2007 Yamaha R1 Main Fuse Location

2007 yamaha r1 main fuse location

Maybe you can also try changing the fuse just for the heck of it, sometimes that helps. Made sure all connections were tight and somehow after weeks of nothing, everything started working. On a LeSabre, the first one is located in the engine compartment on the passenger side near the front. It began as an intermittant problem and has gotten progressively worse over the past couple of months. As partially mentioned, if your terminal locations are opposite of what they previously were, either: 1.

Next

2007 Yamaha R1 Fuse Box

2007 yamaha r1 main fuse location

I hope you are not driving this vehicle with so many faults?. The problem is most likely in your hazard flasher switch. His left blinker and tail light didn … 't work and when he tilted the steering colum down the right blinker and tail light didn't work. Free the cable straps 9 from the regulator bracket, beneath the regulator. Therefore the turn signals and brake lights didn't work.

Next